LeanACADEMY

Select your language

Throughout 2010 I was in contact, in various ways, with around 100 companies. I also visited many of them. The biggest problem I saw was that the maintenance system on the machines and in their surroundings was inadequate, and in some places quite poor. Members of the companies, sometimes mentioning that the machines were old and sometimes that the work was intense, would offer an explanation related to maintenance. The machines and, very often, the area around the machines, the oil, and a layer formed by oil combining with dust and sticking to the floor—sometimes I am talking about a layer of frightening thickness—had become a fact of life. In some places, the amount of dirt and oil had reached a truly unbelievable level and had come to be regarded as normal by the employees.

Well then, without talking any further about the poor condition, let us begin to explain the fundamental causes of this situation and the solutions that should be applied. We can list the fundamental causes of this situation as follows.

Old machine: Many companies, speaking of the age of the machines and of the technology, say that they do not want this situation either, but that there is nothing they can do because of the necessity of investment. Yet there is a very clear fact, and that fact is that there is no such thing as an old machine; there is an unmaintained machine. Technically, the life of a machine is unlimited. Its moving parts wear. What must be done consists of replacing these parts. In this way the machine, mechanically, never grows old; however, from the standpoint of using the machine, it may cease to be economical because of new technologies. For example, the cycle time remains long. The only reason oil runs from one place or another on the machine is that leaks are not repaired and the necessary measures are not taken. The cost created by not performing the necessary maintenance on the machine is always greater than the cost of maintenance. This must be calculated correctly, and the expenditure required for maintenance must be made.

The work is very intense and we cannot spare the time: This is one of the things said most often. The fact that is overlooked is this: if you do not spare time for the machine, it will spare for itself as much time as it wishes. In addition, the repair cost also rises to about ten times as much. What must be done is to establish the autonomous maintenance system. Allocating 5-10 minutes every day for one part of the machine, cleaning it, and maintaining it will be enough. Establishing autonomous maintenance, as you will see below, is very easy.

Let us come to what must be done to set up autonomous maintenance: Autonomous maintenance (Jishu Hozen) means that the people who work on the machine carry out the daily maintenance themselves, and that measures are taken on the machine which improve maintenance and make it easier. What must be done to set up autonomous maintenance:

1.    Determining and classifying the maintenance to be performed: In general, the maintenance to be performed is treated as the maintenance recommended by the machine manufacturer. Yet many of the failures on machines occur for reasons the manufacturer did not foresee and in areas the manufacturer did not foresee. For this reason the machine should be examined thoroughly, and the inspection and maintenance points should be determined. These points are then classified into periods such as daily, weekly, monthly, and yearly. Of these, the daily ones and some of the weekly ones are brought within the scope of autonomous maintenance.

2.    Training the employees: One of the things I have seen in many companies was that the training of employees was insufficient. This shortcoming sometimes reaches quite large proportions. For this reason, employees need to be trained on the maintenance they will perform and on how they will perform it. For this, it will be enough to take employees into training at regular intervals and to give short, concise training. For those who do not have time: preparing one-page visuals in order to make the training easier, and giving 5 minutes of training at the machine every day, will shorten the time considerably. The only way to apply this, however, is for the engineers themselves to take the job on. If you achieve that, life will become easier for everyone.

3.    Making the maintenance tasks easier: On many of the machines, time-consuming operations are required in order to reach a grease fitting, such as opening covers, entering certain sections of the machine, and the like. Yet for daily maintenance we have 5-10 minutes. In order to be able to carry out the tasks within this time, we have to eliminate opening covers, searching for tools, and similar time. In this way maintenance will truly take 5 minutes. In addition, in order to increase the number of maintenance tasks that can be performed by employees who have no knowledge of maintenance, who are found in many companies, preparing correct work instructions and marking visually what is to be done will make our work easier.

In the next article, Autonomous Maintenance's 7 steps are what I will discuss.

We use cookies

We use cookies on our website. Some of them are essential for the operation of the site, while others help us to improve this site and the user experience (tracking cookies). You can decide for yourself whether you want to allow cookies or not. Please note that if you reject them, you may not be able to use all the functionalities of the site.

CookieHint and Consent by reDim GmbH (Opens in a new window)